Five column experiments have been carried out to investigate the effect of flow rate on the breakthrough curves (BTCs) of
phosphate, fulvic acid, and uranium(VI) onto a silica column. Both BTCs of phosphate and fulvic acid, and three BTCs of uranium(VI)
in the presence and absence of phosphate or fulvic acid at high flow rate published in the previous paper [<cite>1</cite>] were compared with corresponding initial parts of BTCs at low flow rate in this paper. Each BTC in this paper was expressed
as both C/Co–t and C/Co–V/Vo plots, where C and Co are the concentrations in the influent and the effluent respectively, t and V are the time and the effluent volume from the
start of injection of pulse solution respectively, Vo is the pore volume of the SiO2 column. Based on the experimental results and the relationship among V, t, and flow rate F, it was found that there are advantages
to using C/Co–V/Vo plot as BTC to study the effect of flow rate. Based on these comparisons of C/Co–V/Vo plots at different flow rates and the theoretical analysis from the Bohart–Adams sorption model, it was found that the right
shift (increase in V/Vo of breakthrough), the left shift (decrease in V/Vo of breakthrough), and the non-shift (non-change in V/Vo of breakthrough) of initial parts of BTCs with increasing flow rate are certain to occur instead of only left shift and that
three different trends of shifts can be mainly attributed to different rate-controlling mechanisms of sorption process.
Authors:Z. Song, X. Huang, Z. Xie, Q. Ge, and R. Wang
The residual fluorine in ammonium uranyl tricarbonate (AUC) cannot be removed, while a large part of residual fluorine in
ammonium diuranate (ADU) can be removed, when AUC and ADU are decomposed and reduced under dry hydrogen atmosphere. UO2 was prepared by decomposing and reducing AUC and ADU in dry hydrogen atmosphere. The defluorination kinetics of UO2 at 500–700°C in atmosphere of 50% H2-50% H2O was investigated. The results show that the defluorination kinetics supports the Lindman's assertion that the residual fluorine
forms a solid-solution in UO2.
The thermal decompositions of dehydrated or anhydrous bivalent transition metal (Mn, Fe, Co, Ni, Cu, Zn, Cd) and alkali rare
metal (Mg, Ca, Sr, Ba) methanesulfonates were studied by TG/DTG, IR and XRD techniques in dynamic Air at 250–850 °C. The initial
decomposition temperatures were calculated from TG curves for each compound, which show the onsets of mass loss of methanesulfonates
were above 400 °C. For transition metal methanesulfonates, the pyrolysis products at 850 °C were metal oxides. For alkali
rare metal methanesulfonates, the pyrolysis products at 850 °C of Sr and Ba methanesulfonates were sulphates, while those
of Mg and Ca methanesulfonate were mixtures of sulphate and oxide.
The title compound 3,3-dinitroazetidinium (DNAZ) 3,5-dinitrosalicylate (3,5-DNSA) was prepared and the crystal structure has
been determined by a four-circle X-ray diffractometer. The thermal behavior of the title compound was studied under a non-isothermal
condition by DSC and TG/DTG techniques. The kinetic parameters were obtained from analysis of the TG curves by Kissinger method,
Ozawa method, the differential method and the integral method. The kinetic model function in differential form and the value
of Ea and A of the decomposition reaction of the title compound are f(α)=4α3/4, 130.83 kJ mol−1 and 1013.80s−1, respectively. The critical temperature of thermal explosion of the title compound is 147.55 °C. The values of ΔS≠, ΔH≠ and ΔG≠ of this reaction are −1.35 J mol−1 K−1, 122.42 and 122.97 kJ mol−1, respectively. The specific heat capacity of the title compound was determined with a continuous Cp mode of mircocalorimeter. Using the relationship between Cp and T and the thermal decomposition parameters, the time of the thermal decomposition from initiation to thermal explosion (adiabatic
time-to-explosion) was obtained.
Authors:J. Ahmed, J. Zhang, Z. Song, and S. Varshney
A thermal analysis of a series of polylactides (PLA) was carried out based on the number of average molecular mass (Mn), and the nature of isomer (D, L and DL). It is confirmed that the glass transition temperature (Tg) of PLA increased as a function of molecular mass irrespective of isomer type except sample with a high polydispersity index.
The melting temperature (Tm) and enthalpy of crystal fusion (ΔHf) of L-isomer increased as the Mn was increased from 1100 to 27500. The degree of crystallinity (χc%) increased as a function of molecular mass. However no crystallization peak was detected in the lower molecular mass range
(550–1400). The non-isothermal crystallization behavior of the PLA melt was significantly influenced by the cooling rate.
Both D and L isomers exhibited insignificant difference in thermal properties and DL lactides exhibited amorphous behavior at identical molecular masses. Change in microstructure showed significant difference
between two isomers. Analysis of the FTIR spectra of these PLA samples in the range of 1200–1230 cm−1 supported DSC observation on crystallinity.
Authors:L. Yang, F. Xu, L. Sun, Z. Zhao, and C. Song
Microcalorimetry was applied to study the effect of cephalosporins (cefazolin sodium and cefonicid sodium) on the E. coli growth. The microbial activity was recorded as power-time curves through an ampoule method with a TAM Air Isothermal Microcalorimeter
at 37°C. The parameters such as the growth rate constant (k), inhibitory ratio (I), the maximum power output (Pm) and the time corresponding to the maximum power output (tm) were calculated. The change tendencies of k, with the increasing of concentration (C) of the two cephalosporins, are similar which show that cefazolin sodium and cefonicid sodium have the same inhibitory mechanism.
The experimental results reveal that cefonicid sodium has a stronger antibacterial activity towards E. coli than that of cefazolin sodium and this was coincide with the clinical manifestations.
Authors:X. Geng, Y. Wu, J. Song, X. Geng, J. Xing, and Z. Lei
The displacement adsorption enthalpies (ΔH) of the refolding of lysozyme (Lys) denatured by
1.8 mol L–1 guanidine hydrochloride (GuHCl)
on a moderately hydrophobic surface at 298 K, pH 7.0 and various (NH4)2SO4
concentrations were determined by using a Micro DSC-III calorimeter. The study
shows that the effect of salt concentrations on the three fractions of the
enthalpy is that with increasing (NH4)2SO4
concentrations, the molecular conformation enthalpy of the adsorbed Lys has
probably no distinct change at 1.8 mol L–1
GuHCl; the adsorption affinity enthalpy (exothermic) becomes more negative;
and the dehydration enthalpy (endothermic) decreases. At lower salt concentrations,
the dehydration, especially squeezing water molecules led by molecular conformation,
which leads to an entropy-driving process, predominates over the adsorption
affinity (also including the orderly orientation of molecular conformation),
while at higher salt concentrations, the latter is prior to the former for
contribution to ΔH and induces an
enthalpy-driving process. Also, the optimal NH4)2SO4
concentration favoring refolding and renaturing of Lys denatured by 1.8 mol
L–1 GuHCl was found.
Authors:Y.-J. Song, S.-H. Meng, F.-D. Wang, C.-X. Sun, and Z.-C. Tan
Polyimide BTDA-ODA sample was prepared by polycondensation or step-growth polymerization method. Its low temperature heat capacities were measured by an adiabatic calorimeter in the temperature range between 80 and 400 K. No thermal anomaly was found in this temperature range. A DSC experiment was conducted in the temperature region from 373 to 673 K. There was not phase change or decomposition phenomena in this temperature range. However two glass transitions were found at 420.16 and 564.38 K. Corresponding heat capacity increments were 0.068 and 0.824 J g–1 K–1, respectively. To study the decomposition characteristics of BTDA-ODA, a TG experiment was carried out and it was found that this polyimide started to decompose at ca 673 K.
Authors:L. Yang, S. Qiu, F. Xu, L. Sun, Z. Zhao, J. Liang, and C. Song
The effects of Amoxicillin Sodium and Cefuroxime Sodium on the growth of E. coli DH5α were investigated by microcalorimetry. The metabolic power-time curves of E. coli DH5α growth were determined by using a TAM air isothermal microcalorimeter at 37�C. By evaluation of the obtained parameters,
such as growth rate constants (k), inhibitory ratio (I), the maximum heat power (Pm) and the time of the maximum heat power (tm), one found that the inhibitory activity of Amoxicillin Sodium vs. E. coli DH5α is enhanced with the increasing of the Amoxicillin Sodium concentration, and the Cefuroxime Sodium has a stimulatory effect on the E. coli DH5α growth when the concentration is about 1 μg mL−1. The IC50 for the Amoxicillin Sodium and the Cefuroxime Sodium are 1.6 and 2.0 μg mL−1, respectively, it implicates that the E. coli DH5α is more sensitive to Amoxicillin Sodium than Cefuroxime Sodium.