Abstract
This paper presents the results of testing the flammability and fire hazard of butadiene (BR), butadiene-acrylonitrile (NBR) and butadiene- styrene (SBR) rubbers with the use of oxygen index test, ignition temperature measurement, cone calorimetry and inverse liquid chromatography. Toxicometric indices, RTFH CO/CO2, WLC50SM and the concentration of polycyclic aromatic hydrocarbons (PAH) have been determined. The results obtained have been interpreted from the point of view of the chemical constitution of the polymers tested.
Introduction
Polymers and polymeric materials are now commonly used in all the fields of economy (industry, agriculture, housing, land, sea, and air transports). In most cases polymers are flammable products. There is a group of polymers such as polyolefines, cellulose, and others that undergo complete combustion in a medium that is poorer in oxygen than atmospheric air. Only few polymers, designed for special applications, can be accepted as inflammable or flame-retardant due to their chemical composition and molecular structure. Generally speaking, the flammability of polymers depends on the content of carbon and hydrogen in their macromolecule, which ranges from over 85% of C and 14% of H to 0% of hydrogen, e.g., in inflammable nitrozofluoric polymers. The reduction in the flammability of polymeric materials and fire hazard resulting from their use consists in selecting properly the composition of polymeric blends, which can be achieved by using appropriately selected flame-retardant compounds and fillers or nano-fillers, surface modification of components or products. Studies on the preparation of polymeric composites and nano-composites that would be thermally stable and show limited flammability or self-extinguishing capability constitute now one of the more dynamically developed trends in material engineering.
The combustion process of solids can proceed according to the hetero- or homo-phase mechanism depending on their structure. The hetero-phase combustion consists in adsorbing oxygen on the material surface under combustion and flame-less oxidation at the interface. The combustion according to the homo-phase mechanism results from the reaction between the volatile products of thermal decomposition and oxygen with no interfacial surface between reagents [1, 2]. Generally in polymers, their combustion proceeds according to an intermediate mechanism with visible features of homo-phase and hetero-phase combustions.
The combustion of elastomers is a complex process that depends on the chemical constitution and physical structure of macromolecules as well as on the chemical reactions and physical phenomena taking place in the sample under testing, its boundary layer and flame.
The present article contains a fragment of studies associated with the flammability and fire hazard of butadiene, butadiene–acrylonitrile and butadiene–styrene rubbers commonly used in the rubber industry.
Experimental
Materials
The diene rubbers used in our studies included: cis-1,4-polybutadiene, SKD II, containing 87–93% of cis 1,4 mers, made in Russia (BR), butadiene-styrene rubber, KER 1500, containing 23.5% of styrene, from Synthos S.A. (SBR) and butadiene-acrylonitrile rubber, Perbunan 2255VP, containing 22% of acrylonitrile, from Lanxess (NBR).
Methods
The flammability of elastomers was determined by the method of oxygen index using an apparatus of our own construction [3]. For flammability tests, samples of dimensions 100 × 10 × 4 mm were prepared. Using a constant rate of nitrogen flow amounting to 400 l/h, the oxygen flow rate was selected so that a 50 mm sample length burned within time t = 180 s. The sample top was ignited for 15 s by means of a gas burner supplied with a propane–butane mixture [4–6]. The value of oxygen index (OI) was expressed in fractions on the basis of the oxygen volume fraction in the oxygen–nitrogen mixture.
The determinations of flammability in air were also performed, measuring the combustion time of samples whose shape, dimensions, and location as well as ignition time were the same as those in the case of the oxygen index method [4–6]. It was quite difficult to prepare shaped samples for flammability measurements due to their adhesion to the metal mold, but this problem was solved by subjecting the elastomers tested to slight cross-linking by means of dicumyl oxide.
The flammability of the polymers under testing was also determined by the method of cone calorimeter according to standard ISO 5660-1.2002, using an apparatus from Atlas Electric Devices Company. This apparatus is used for integrated tests of materials in terms of their fire characteristics. Elastomer samples of dimensions (100 × 100 ± 1) mm and thickness (2.0 ± 0.5) mm, conditioned to constant weight at a temperature of (20 ± 0.5) °C and RH (50 ± 0.5) %, were tested in a horizontal position using a heat radiation flux with a density of 35 kW/m2. During testing the following parameters were recorded: initial sample weight, time for ignition, sample weight during the test, the temperature of inlet gases and their pressure and the concentrations of O2, CO2, and CO in outlet gases, extinction coefficient and test duration. The time for ignition means the moment from the beginning of test, when the flame lasts at least for 10 s.
The temperature of ignition (TZ), determined as the lowest temperature, at which a polymer sample heated in a strictly specified way releases a sufficient quantity of gases to produce a mixture with air that ignites from the flame of a gas burner, was determined by means of an apparatus from ANKO. Disintegrated rubber samples, 0.5 g in weight, were placed in acid resistant steel test-tubes equipped with metallic lids with holes for gas to escape from the heated material. The test-tubes were electrically heated in an aluminum block within the temperature range 150–400 °C.
The combustion heat of elastomers was determined by means of a bomb calorimeter.
The composition of boundary layer was determined from the results of elementary analysis.
The toxicity of the gas products of elastomer decomposition and combustion was assessed from the results obtained by the method of cone calorimetry (
) and on the basis of the quantitative chemical determination of the specific emission of CO, CO2, HCN, NO2, HCl, and SO2 at temperatures of 450, 550, and 750 °C, according to standard PN-B-02855:1988 (WLC50SM).
The polycyclic aromatic hydrocarbons (PAH) were determined in the rubbers tested and in the gaseous products of their thermal decomposition. For that end elastomers were extracted with acetone for 48 h at room temperature and the extract obtained was analyzed for the content of PAH. The gaseous products of elastomer thermal decomposition were obtained by their pyrolysis performed in glass pyrolytic test-tubes. The pyrolysis products were transferred by means of a rubber hose to a glass scrubber containing acetone. The determination of 11 PAHs was carried out the method of liquid chromatography in the inverted phase system. The HPLC Lachrom system (Merck Hitachi) consisted of L-7100 isocratic pump, UV L-7400 detector and LiChrospher 100 RP-18 5 μm column (Merck). The analysis was performed by the method of standard addition (PAH Calibration Mix—Supelco) under the following conditions: 20 μl of sample, the mobile phase: acetonitrile–water (75:25), flow rate: 1 mL/min, detection at 280 nm. Reagents with HPLC purity were provided by Merck.
Results and Discussion
The combustion of most elastomers is accompanied by the formation of considerable amounts of liquid products of their thermal decomposition, which flowing down along the sample transfer heat and increase contact with oxygen. These phenomena, considerably impeding the measurements of flammability, take place especially during the combustion of those polymers that are, above all, degraded under the influence of elevated temperatures [2, 7].
Our tests have shown that they occur to a limited extent in the case of investigated diene rubbers and to the largest extent during the combustion of polybutadiene. The elastomers under investigation are susceptible to thermal cross-linking; moreover, SBR rubber and especially NBR, due to strong intermolecular interactions as shown by their cohesion energy density, are susceptible to form solid products of thermal decomposition, which facilitates carbonization processes (Table 1). The susceptibility to thermal cross-linking and especially that to form solid products of thermal decomposition significantly influences the structure of boundary layer between the solid and gaseous zones of combustion. The structure of this layer plays an important part in combustion processes as the transport of mass and energy between flame and sample proceeds through this layer. In the case of BR, the boundary layer consists of a cross-linked polymer and a small quantity of liquid destruction products. During the combustion of SBR, and especially NBR, the boundary layer is more thermally stable and porous as it is formed from both the cross-linked and partially carbonized elastomers. Therefore, this layer impedes the flow of mass and energy to a larger extent.
The results of diene rubbers flammability investigations
| Sample | Cohesive energy density (CED)/MJ × m−3, [7, 8] | Heat of combustion/kJ × kg−1 | T z/°C | OI | T s/s | Composition of boundary layer/%a |
|---|---|---|---|---|---|---|
| NBR | 432 | 39,600 | 335 | 0.265 | 300 | C = 70.02; H = 8.23 |
| N = 4.44; S = 1.2; O = 16.11 | ||||||
| SBR | 335 | 43,400 | 348 | 0.260 | 206 | C = 71.83; H = 8.60 |
| S = 0.43; O = 19.14 | ||||||
| BR | 288 | 43,300 | 336 | 0.259 | 180 | C = 73.48; H = 7.95 |
| O = 18.57 |
The results of elementary analysis of boundary layer after 30 s of elastomer being under combustion in air. The boundary layer was separated from the sample in depth ≤1.0 mm. The results of elementary analysis of investigated elastomers
NBR: C = 82.93; H = 9.39; S = 1.57; O = 0.52
SBR: C = 88.46; H = 10.29; S = 0.54; O = 0.71
BR: C = 88.60; H = 10.79; S = 0.51; O = 0.10
For that reason NBR is characterized by the lowest flammability from among the rubbers investigated, determined by both OI and combustion time in air (ts) (Table 1).
The lowest flammability of NBR results also from the comparative analysis of combustion heats of the elastomers tested as in most cases a higher combustion heat corresponds to a higher flammability (Table 1) [8].
BR and SBR rubbers are characterized by comparative flammability determined by OI and ts, but the ignition temperature of SBR is the highest among those of the polymers under investigation.
A significant influence on the polymer flammability is exerted by both the rate of mass loss during combustion and the type of the products being formed. Among the polydienes tested the lowest rate of mass loss is shown by NBR (Table 2). Thus, in the case of this elastomer, the lowest quantity of volatile and flammable products of its thermal decomposition enter the flame through the boundary layer. Moreover, during the destruction processes of NBR nitrogen can be released [1] to form nitrogen compounds as confirmed by the test results of flammability (Table 4). Especially nitrogen but also its compounds reduce the yield of free radical combustion reactions taking place in flame, which is also the reason why NBR shows the lowest flammability in comparison to that of BR or SBR.
The means values of parameters of diene rubbers determined by cone calorimeter
| Parameter | NBR | SBR | BR |
|---|---|---|---|
| Time to sustained ignition/s | 50.9 | 70.96 | 67.17 |
| Average heat release rate/kW × m−2 | 1408.23 | 975.65 | 757.81 |
| Peak heat release rate/kW × m−2 | 3362.76 | 2248.28 | 3787.89 |
| Total heat release/MJ × m−2 | 98.71 | 87.88 | 84.5 |
| Average effective heat of combustion/MJ × m−2 | 51.09 | 34.81 | 42.12 |
| Average mass loss rate/gs × m−2 | 40.71 | 50.40 | 58.24 |
| Maximum mass loss rate/gs × m−2 | 71.88 | 66.21 | 79.24 |
| Average specific extinction area/m2 × kg−1 | 717.9 | 1098.53 | 772.83 |
| Average CO yield/kg × kg−1 | 0.091 | 0.082 | 0.1198 |
| Average CO2 yield/kg × kg−1 | 3.153 | 2.43 | 3.0199 |
The formation of flammable gaseous products sustaining the combustion of polymers and polymeric materials proceeds due to their thermal decomposition. From the review of scientific literature it follows that in addition to conduction, convection and radiation, a considerable source of heat energy indispensible for sustaining the decomposition of polymers can come from the strongly exothermic oxidative reactions taking place due to the chemisorption of oxygen in the boundary layer between the solid and gaseous phase of combustion [2]. Our test results show that these reactions exert a considerable effect on the combustion processes of the rubbers under investigation, regardless of their chemical constitution as indicated by the oxygen-rich boundary layers (Table 1). The lowest contribution of oxygen chemisorption was found in the case of NBR.
The oxygen index method is commonly used to test the flammability of polymers. However, it should be stressed that the values of OI can be used only in the case of comparative assessment of flammability, but they cannot be a base to classify materials with respect to fire hazard. So far no ideal method has been found for testing polymer properties that would decide about their fire hazard. It is accepted that the basic properties characterizing the behavior of polymers under fire conditions include: ignitability described as ignition time, total emitted heat, smoke emission described by its mass average optical density, and the toxicity of the products of thermal decomposition and combustion. These properties can be determined on the basis of test results obtained by the method of cone calorimetry (Tables 2, 3, 4). The comparative analysis of tests presented in Table 2, leads to a conclusion that NBR, showing the lowest flammability among those of the remaining elastomers tested, poses also the smallest fire hazard from the point of view of smoke emission. However, taking into account the total heat emitted and the average and maximum rates of heat emission, its fire hazard is greater than those of BR and SBR. The highest quantity of emitted smoke is shown by SBR due to the content of aromatic groups in its macromolecules.
The diene rubbers properties describing their behaviour in the fire conditions
| Parameter | NBR | SBR | BR |
|---|---|---|---|
| 1/tflashover, kW × m−2s−1 | 66.06 | 31.68 | 56.37 |
| 0.0339 | 0.0236 | 0.0406 |
The results of toxicity investigations of the products of thermal decomposition and flammability of diene rubbers
| Sample | Temperature/°C | Emission, mg/g | Ratio CO2/CO | Toxicometric Index | ||||||
|---|---|---|---|---|---|---|---|---|---|---|
| HCN | NO | NO2 | CO | SO2 | CO2 | WLC50M | WLC50SM | |||
| NBR | 450 | 17.02 | 5.71 | 0.00 | 69.37 | 7.88 | 431.85 | 6.22 | 7.23 | 9.13 |
| 550 | 8.09 | 4.41 | 0.80 | 201.7 | 12.73 | 1752.26 | 8.68 | 7.38 | ||
| 750 | 3.63 | 8.19 | 2.95 | 93.16 | 0.71 | 2980.66 | 31.99 | 12.79 | ||
| SBR | 450 | – | – | – | 58.57 | 26.16 | 115.56 | 1.97 | 18.66 | 17.25 |
| 550 | – | – | – | 190.4 | 9.405 | 2243.62 | 11.78 | 13.22 | ||
| 750 | – | – | – | 99.39 | 8.627 | 2254.36 | 22.68 | 19.88 | ||
| BR | 450 | – | – | – | 126.2 | 58.57 | 55.07 | 0.43 | 14.12 | 19.65 |
| 550 | – | – | – | 266.9 | 190.4 | 4068.8 | 15.24 | 8.31 | ||
| 750 | – | – | – | 21.47 | 99.39 | 3964.54 | 184.65 | 36.52 | ||
Fire hazard results also from oxygen consumption during the combustion of polymers or polymeric materials. Our test results show that from this point of view, the smallest fire hazard is posed by SBR (Fig. 1).
The mass loss rate of diene rubbers determinated by cone calorimeter
Citation: Journal of Thermal Analysis and Calorimetry J Therm Anal Calorim 102, 3; 10.1007/s10973-010-0902-x
The mass loss rate of diene rubbers determinated by cone calorimeter
Citation: Journal of Thermal Analysis and Calorimetry J Therm Anal Calorim 102, 3; 10.1007/s10973-010-0902-x
The mass loss rate of diene rubbers determinated by cone calorimeter
Citation: Journal of Thermal Analysis and Calorimetry J Therm Anal Calorim 102, 3; 10.1007/s10973-010-0902-x
connected with carbon oxide and dioxide according to Eq. 2 (Table 3).
is the lethal concentration respectively CO and CO2 to cause a 50% lethality of testing animals during 30 min exposure.The analysis of results listed in Table 3, leads to a conclusion that butadiene and nitrile rubbers pose a considerably greater fire hazard expressed by the values of both 1/tflashover and RTFHCO/CO2 in relation to butadiene–styrene rubber. It should be clearly mentioned that the diene rubbers tested by us pose a greater fire hazard than that of the commonly used polyolefines such as polyethylene (PE) and polypropylene (PP). The values of 1/tflashover of PE and PP amount to 20.15 and 44.22, respectively, and those of 
equal to 0.0051 and 0.0138, respectively [9, 10].
is the lethal concentration of gaseous product of thermal decomposition and combustion of testing material which cause a 50% lethality of testing animals during 30 min exposure.According to standard PN-B-02855:1988 the value of WLC50SM is the base of classifying the products of thermal decomposition and combustion into the following groups:
WLC50SM ≤ 15—very toxic products
15 ≤ WLC50SM ≤ 40—toxic products
WLC50SM > 40—moderately toxic products
From the toxicometric indices determined it follows that butadiene rubber and butadiene-styrene rubber belong to the group of toxic polymers, while butadiene–acrylonitrile rubber belongs to the group of very toxic polymers. The considerably higher value of WLC50SM of NBR in comparison to those of BR and SBR is associated with the emission of NO, NO2, and HCN (Table 4).
In recent years increasingly high importance has been ascribed to the problem of the emission of PAH formed during the thermal decomposition and combustion of polymers and polymeric materials as well as those contained in polymers. Based on the analyses performed by the method of liquid chromatography, we have determined the concentrations of 11 best known polycyclic compounds in the gaseous products of the thermal decomposition and combustion of diene rubbers (Table 5). The highest concentrations of acenaphthylene, fluorene and carcinogenic dibenzo(a,h)anthracene consisting of five condensed rings are observed in BR. The high concentrations of PAH in the process of BR thermal decomposition result from the fact that the macromolecules of BR contain 87–93% mers with a cis 1–4 structure. During the initial stage of pyrolysis butadiene mers react, according to Diels-Alder's mechanism, with alkanes (C1–C3) and alkenes (C2–C6), previously resulted from destruction processes, to form basis aromatic compounds such as benzene, toluene, or styrene [13–15].
Polycyclic aromatic hydrocarbons in μg/mass sample in the gaseous products from the thermal decomposition and combustion of diene rubbers
| Sample | BR | SBR | NBR | Amount condensed rings |
|---|---|---|---|---|
| Naftalen | 3.005348 | 35.08016 | 5.633333 | 2 |
| Acenaftylen | 133.1717 | 29.54545 | – | 2 |
| Acenaften | 2.801264 | 143.0447 | – | 2 |
| Fluoren | 23.84917 | 8.793478 | 4.196217 | 2 |
| Fenantren | – | 24.09389 | 4.587242 | 3 |
| Fluoranten | – | 4.83871 | 12.04918 | 3 |
| Piren | 1.599166 | 12.73466 | 1.53944 | 4 |
| Benzo(b)Fluoranten | 1.373562 | 2.328704 | 6.787745 | 4 |
| Benzo(k)Fluoranten | 1.678937 | 3.16289 | 4.617404 | 4 |
| Benzo(a)Piren | 2.777143 | 0.999265 | 6.90447 | 5 |
| Dibenzo(a,h)Antracen | 3.021656 | 2.030371 | 5.112 | 5 |
Mass sample 2 mg
Then PAH are formed as a result of mutual condensation of aromatic rings or subsequent reactions between aromatic compounds and olefins. Considerably lower concentrations of PAH in the thermal decomposition products of SBR and NBR result from lower contents of diene mers in their macromolecules, and in the case of nitrile rubber, also from the proceeding processes of carbonization. According to our opinion the relatively high concentrations of naphthalene, acenaphthylene, acenaphthene and phenanthrene in the case of butadiene-styrene rubber can be connected with the modification of this elastomer with naphthene oils, which undoubtedly are their precursors [16].
Our test results show that PAH are also present in the rubbers under investigation (Table 6). The concentrations of PAH in this case are however low, connected with the presence of two- and three-cyclic compounds, whose carcinogenic effects are considerably weaker in comparison with compounds consisting of a higher number of condensed rings. Thus, the use of these polymers does not pose a health hazard. A big hazard occurs under fire conditions as PAH are formed first of all in the processes of thermal decomposition and combustion of the rubber under investigation.
Polycyclic aromatic hydrocarbons in μg/mass sample in pure diene rubbers
| Sample | BR | SBR | NBR | Amount condensed rings |
|---|---|---|---|---|
| Naftalen | – | – | 0.2791 | 2 |
| Acenaftylen | – | – | 0.3759 | 2 |
| Acenaften | 0.1412 | – | 0.0775 | 2 |
| Fluoren | – | – | 0.0712 | 2 |
| Fenantren | 0.0583 | 0.2323 | 0.0802 | 3 |
| Fluoranten | – | – | – | 3 |
| Piren | – | 0.1846 | – | 4 |
| Benzo(b)Fluoranten | – | – | – | 4 |
| Benzo(k)Fluoranten | – | – | – | 4 |
| Benzo(a)Piren | – | – | – | 5 |
| Dibenzo(a,h)Antracen | – | – | – | 5 |
Mass sample 2 mg
Conclusions
Among the diene rubbers tested, butadiene–acrylonitrile rubber is characterized by the lowest flammability determined by OI and ts; this rubber poses also the smallest fire hazard from the point of view of smoke emission. However, the products of its decomposition and combustion show the highest degree of toxicity (WLC50SM).
Conduction, convection, and radiation not constitute the basic source of heat energy indispensable to sustain the thermal decomposition of the rubbers during their combustion. A considerable role is played also by exothermic reactions in the boundary layer between solid and gaseous phases. These reactions take place to the smallest extent in NBR.
The products of thermal decomposition of the polydienes tested include also PAH.
References
1. Troitzch, J 1990 International plastics flammability handbook Hanser Publishers Munich, Viena, New York.
2. Janowska, G, Przygocki, W, Włochowicz, A 2007 Palność polimerów i materiałów polimerowych WNT Warszawa.
3. Ślusarski L , Janowska G, Szkodziński A, Niedomagała M, Harwaziński A. Układ do pomiaru wskaźnika tlenowego tworzyw sztucznych, naturalnych lub gumy, Patent PRL 129411. 1987.
4. Ślusarski, L, Janowska, G 1982 Palność elastomerów. Polimery 27:13.
5. Babrauskas, V 1994 Describing product fire performance—manufacturers, versus modelers needs. Fire Mater 18:289 .
6. Rybiński, P, Janowska, G, Helwig, M, Dąbrowski, W, Majewski, K 2004 Flammability of butadiene–acrylonitrile rubbers. J Therm Anal Calorim 75:249 .
7. Janowska G . Thermal stability and flammability of elastomers. Zeszyty Naukowe Politechniki Łódzkiej, Łódź. 1998;801: 1–107.
8. Johnson, PR A general correlation of the flammability of natural and synthetic polymers. J Appl Polym Sci 1974 18:491 .
9. Helwig M , Paukszta D. Flammability of composites based on polypropylene and flax fibres in molecular crystal and liquid crystal, vol 354. Philadelphia: Gordon and Breach Science Publisher; 2000.
10. Paukuszta, D, Borysiak, S 2005 Structure of isotactic polypropylene in composites with natural fibres obtained in various processing methods. Fibres Text 53:107–109.
11. Janowska, G, Rybiński, P, Krauze, S 2006 The effect of the curing agent type on the flammability of butadiene–acrylonitrile rubbers. Polimery 51:735.
12. Rybiński, P, Janowska, G, Antkiewicz, W, Krauze, S 2005 Thermal stability and flammability of butadiene–acrylonitrile rubber cross-linked with iodoform. J Therm Anal Calorim 81:9 .
13. Cypres, R, Braekman-Danheux, C, Delaunois, C, Halloin, V 1991 Aromatisation of 1,3-butadiene under pressure. Thermochem Acta 179:99 .
14. Williams, PT, Bottril, RP 1995 Sulfur–polycyclic aromatic hydrocarbons in tyre pyrolysis oil. Fuel 74:736 .
15. Wang, Z, Li, K, Lambert, P, Yang, C 2007 Identification, characterization and quantitation of pyrogenic polycylic aromatic hydrocarbons and other organic compounds in tire fire products. J Chromatogr A 1139:14 .
16. Stang, G Oleje naftenowe mniej rakotwórcze. Elastomery 2001 1:3.
