Abstract
Gasification of char derived from sewage sludge was studied under different oxidizing atmospheres containing CO2, O2 or H2O. The gasification tests were carried out in thermobalance at different temperatures and oxidizing reagent concentrations. The most efficient were the gaseous mixtures containing oxygen. The reaction took place at temperature 400–500 °C, whilst in the case of CO2 and steam much higher temperatures (700–900 °C) were necessary to complete the conversion. Two rate models for gas–solid reaction were applied to describe the effect of char conversion on reaction rate. The shrinking core model for reaction-controlled regime was found to be the best for predicting the rate of char gasification in CO2 and O2 atmosphere. The experimental data for steam gasification of the char were fitted best by the first-order kinetics. The kinetic parameters estimated from the experimental data are in accordance with the literature for lignocellulosic char gasification and are the first published for sewage sludge char gasification.
Introduction
Sewage sludge is regarded as the residue produced by the wastewater treatment process. Currently the most widely available option of sludge utilization in the EU are according to Fytili and Zabaniotou [1] the agriculture utilization and the waste disposal sites. However, there is a wide range of other uses for sludge, which exploit its energy, namely the thermal processes. The thermal and chemical processes of sewage sludge conversion consist of pyrolysis, gasification direct combustion and co-combustion [2]. Pyrolysis as the first chemical step in gasification and combustion plays an important role because its conditions highly affect the yields of char and its reactivity [3, 4]. The conversion of char occurs at higher temperatures when most of thermal decomposition processes are finished. Thus, in gasification process the primary pyrolysis products, condensable and non-condensable vapours and mainly char undergo secondary reactions with gasification reagent forming additional amounts of synthesis gas. Apart from being used as potential fuel, the product of gasification, synthesis gas is a useful raw material for chemical industries.
Char gasification kinetics depends on the gasifying agent used and the operation conditions, such as pressure and temperature [5]. On the other side, type and composition of fuel used for char preparation strongly affect the rate of gasification [6, 7]. Gasification is usually carried out with air, oxygen and steam mixtures. The gasification process is very often performed with steam as the gasifying agent; the advantage of using steam is that this process yields higher amounts of hydrogen [7]. However, nowadays when there is a worldwide discussion about utilization of carbon dioxide, the so-called dry gasification by means of CO2 is also of great importance [8, 9]. Also in some places Integrated Coal Gasification Combined Cycle power plants have been developed to reduce CO2 emissions [6]. The presence of CO2 can improve char conversion and decrease the volume of gasification residue [10].
Gasification of sewage sludge as well as co-gasification with coal as integrated processes involving primary and secondary reactions have been widely investigated during recent years [11–18]. However, the literature on the reaction of sewage sludge char with an oxidizing agent, which is considered as the most important step in the overall processes process, is very scarce, in contrast to the literature concerning the coal and biomass chars gasification reactions.
The information which is acquired with kinetic studies can be usefully applied in different fields, such as the interpretation of reaction mechanisms and catalytic phenomena, molecular behaviour, the optimization and development of new chemical processes as well as reactors modelling and simulation. Therefore, the study of chemical reaction kinetics is of interest to both chemists and chemical engineers using and elaborating reaction rates data on different objectives [19]. Then, the study can be oriented to define the kinetics of each reaction in the pattern.
Char gasification kinetics is of great importance in the design of gasification reactors. This is because gasification is a slower process than the initial pyrolysis [20]. Gasification results in continuous changes in char composition. Hence, the char reactivity tends to vary with degree of conversion or time. Therefore, the first-order kinetics often holds only for a part of the conversion interval.
In general, there are many publications concerning gasification kinetics of chars obtained from different types of coal [6, 21–23] or any types of biomass [4, 24–26]. However, according to our knowledge there are no publications on gasification kinetics of char derived from sewage sludge, except the study of Scott et al. [26], who measured the rate of gasification by CO2 of different chars, including char derived from sewage sludge. They found that this char was the most reactive one, due to the largest amount of inorganic material, components of which catalyse the gasification of carbon by CO2. The reactivity of pyrolyzed sewage sludge in air and carbon dioxide was studied by Inguanzo et al. [27].
In this article, the effect of oxidizing reagent on the kinetics of gasification of char derived from sewage sludge was studied using thermogravimetric analysis and modelling. Gasification rate equations and kinetic parameters for different oxidizing agents (O2, H2O and CO2) were obtained. Kinetic analysis is mainly used as a tool for extracting valuable information about the gasification step from a series of measurements with many data points in the form of models with limited number of parameters. We believe that these models can be eventually extrapolated to the industrial applications.
Materials and methods
Gasification of sewage sludge char was performed in a thermobalance (Netzsch STA 409 PG, Germany). The digested sewage sludge containing about 46 wt% of ash (on dry mass basis) from Waste Water Treatment Plant in Lodz, Poland was used for char preparation. The results of proximate and ultimate analysis of sewage sludge are presented in Table 1. Proximate analysis of moisture, volatiles, char and ash was performed in preliminary experiment where the samples of sewage sludge were heated to 1000 °C in the inert gas (argon) and then kept at this temperature in air atmosphere to burn out the char formed during the pyrolysis. The contents of C, H, N, S and O elements were determined by an elemental analyser (CE Instruments NA 2500). The results from elemental analysis were used to estimate the heating value of the studied sample.
Proximate and ultimate analyses of sewage sludge samples
| Proximate analysis/wt% | Ultimate analysis/wt% | HV/MJ kg−1 | |||||||
|---|---|---|---|---|---|---|---|---|---|
| Moisture | Volatiles | Char | Ash | N | C | H | S | O | |
| 5.3 | 44.6 | 7.4 | 42.7 | 2.8 | 26.0 | 3.5 | 1.1 | 23.9 | 10.1 |
The char was obtained by devolatilization of sewage sludge in a quartz fixed-bed reactor (20 mm internal diameter) heated by an electric furnace in at 1000 °C under an argon stream. The sample of dried and ground sewage sludge was heated at the constant heating rate of 100 °C/h and then held in final conditions (1000 °C) for about 120 min. Then the char was cooled under a flow of argon to room temperature, and sieved. The fraction of the char particle diameter less than 70 μm was used for gasification tests.
The gasification tests with sewage sludge char were performed under atmospheric pressure. The thermobalance was equipped with the water vapour furnace enabling a measurement in the atmosphere containing a controlled amount of steam. Except water vapour, mixtures of oxygen or carbon dioxide diluted with argon were used for gasification. The total flow rate of gas introduced into the thermobalance during the experiments was 50 cm3/min (in the case of reactive gas containing steam, the total flow rate was greater than 50 cm3/min by a stream of water vapour produced in the steam generator). The char sample was placed in an alumina crucible 5 mm diameter and 3 mm height. The mass of sample used was about 20 mg. The rates of char gasification were measured under isothermal conditions at different temperatures depending on the gasifying agent used.
To determine the temperature range where different reactive gases are active in the gasification reaction, preliminary experiments were performed, additionally under dynamic conditions. During these experiments the char samples were heated at the constant heating rate of 10 °C/min from room temperature to 1000 °C. Three different oxidizing atmospheres were applied: 10 vol.% O2/90% Ar; 50% CO2/50% Ar and 16% H2O/84% Ar.
Results and discussion
Figure 1 shows a comparison of TG (Fig. 1a) and DTG (Fig. 1b) profiles for the char gasification with different oxidizing agents under non-isothermal conditions. The gas containing 10% of oxygen reacts with char at relatively low temperatures. In this case the reaction starts at about 400 °C and reaches the maximum rate at 540 °C. The gases containing 50% of CO2 and 16% of H2O in argon react with char only above 700 and 750 °C, respectively. The maximum rate with carbon dioxide was observed at 806 °C, whereas for steam it was shifted to 934 °C. It is worth to notice that the maximum reaction rate measured at dynamic conditions was similar for all oxidizing reagents used.
TG (a) and DTG (b) curves for thermochemical decomposition of sewage sludge char under different atmospheres
Citation: Journal of Thermal Analysis and Calorimetry J Therm Anal Calorim 104, 2; 10.1007/s10973-010-1032-1
As can be seen in the Fig. 1, there are differences in total mass loss depending on the oxidizing reagent used. At the final temperature of 1000 °C the total mass loss in the case of oxygen was 18% of the initial mass, whilst in the case of CO2 and steam it was about 21%. The higher mass loss for CO2 and H2O may be explained by the interaction of these gases with some components of a mineral layer (ash) of the char, which was observed during our studies of catalytic effects of ash in pyrolysis and gasification processes [28]. This interaction can be also seen, before the chemical reaction starts (see Fig. 1), as a small increase of the sample mass, which was probably caused by adsorption of gaseous reagents on the solid surface. It is generally accepted that the adsorption of the gas component is the first step in the mechanism of char gasification process [4].
Experimental conversion for thermochemical decomposition of pyrolysis char under different temperatures and atmospheres
Citation: Journal of Thermal Analysis and Calorimetry J Therm Anal Calorim 104, 2; 10.1007/s10973-010-1032-1
To determine the effect of oxidizing agent concentration on the gasification rate, experiments at fixed temperature (500, 800 and 850 °C) for each reagent (O2, H2O and CO2), respectively, were performed. These data are presented in Fig. 2d–f.
The reaction rate constants kv and ks can be calculated using the experimental results shown in Fig. 3a, c, e, and b, d, f from the slopes of plots representing Eqs. 5 and 6, respectively. These figures show the application of the first-order and shrinking core models to the experimental results obtained for the gasification of sewage sludge char at different temperatures and for different oxidizing agents.
Plots of the linearized volumetric first-order (left side plots) and shrinking core (right side plots) model equations for sewage sludge char gasification under different atmospheres. Effect of temperature
Citation: Journal of Thermal Analysis and Calorimetry J Therm Anal Calorim 104, 2; 10.1007/s10973-010-1032-1
The relationship between the left-hand side of Eqs. 5 or 6 versus time should be a straight line to prove validity of the model. Figure 3 shows the application of these two equations to the experimental results obtained for the gasification of char at different temperatures and oxidizing atmospheres. A range of conversions varied from 0.05 to 0.95 is presented on the plots. The analysis of data presented in Fig. 3 leads to the conclusion that the first-order reaction model can be only applied for the steam gasification in the whole range of conversion (0.05–0.95). In the case of oxygen and carbon dioxide the shrinking core model predicts the experimental data much better; however, for the reactive gas containing 10 vol.% oxygen, the model is valid only for the char conversion below 90%. The validity of the first-order kinetics may suggest that steam gasification of char proceeds according to different mechanism than that for gasification with carbon dioxide and oxygen. As it was mentioned above, the shrinking core model (as well as the first-order model) does not predict the experimental data for oxygen over 85–93% of conversion. It might be possible that diffusion limitations can play an important role in this conversion region. The sewage sludge char is a porous material with a complex structure (distribution of pores within the particle) [26], which makes it difficult to reach the solid surface by reacting gas in the micro-porous region where the char is only available at the end of the reaction. As can be seen from Fig. 3b, the shrinking core model in the regime of chemical kinetic control reaction can be used only up to certain maximum value of conversion which decreases with increasing temperature (from about 93% at 450 °C to about 85% at 550 °C). This finding shows that the effect of intra-particle mass transfer on the rate of reaction is more pronounced at higher temperatures as it could be expected. The diffusion limitation is not important in the case of carbon dioxide, although the same model was proved to be applicable. However, at 800–950 °C, where the CO2 gasification was studied, the reaction was much slower compared to the other gasifying agents (see Fig. 6), so the dry gasification by CO2 was almost certainly limited by the chemical reaction kinetics.
The values of the reaction rate constants determined from the slope of straight lines drawn for the better-fitting models are given in Table 2. Upon correlating these values of rate constants with the temperature (Table 2) according to Arrhenius law (Fig. 4), the activation energy (E) and the pre-exponential factor (ko) were obtained.
Kinetic parameters for char gasification with different oxidizing reagents
| Reactive atmosphere | Temperature/°C | k v /s−1 | k s /s−1 |
|---|---|---|---|
| 10 vol.% O2/90% Ar | 450 | 7.044 × 10−5 | |
| 500 | 2.221 × 10−4 | ||
| 550 | 7.0611 × 10−4 | ||
| 50 vol.% CO2/50% Ar | 800 | 4.284 × 10−5 | |
| 850 | 1.965 × 10−4 | ||
| 900 | 1.210 × 10−3 | ||
| 16 vol.% H2O/84% Ar | 750 | 1.619 × 10−4 | |
| 800 | 5.482 × 10−4 | ||
| 950 | 1.210 × 10−3 |
Arrhenius plots for sewage sludge char gasification with different oxidizers
Citation: Journal of Thermal Analysis and Calorimetry J Therm Anal Calorim 104, 2; 10.1007/s10973-010-1032-1
Table 3 shows the values of parameters ko and E, obtained for three different gasifying reagents. The values of pre-exponential factors and activation energy are in the expected range determined for different biomass char gasification reactions (e.g. Di Blasi [4], Fermoso et al. [7], Klose and Woelki [25]). However, the activation energy for carbon dioxide (223 kJ/mol) is slightly lower than the value of 260 kJ/mol given by Scott et al. [26] for char derived from sewage sludge containing similar amount of ash.
Comparison of kinetic parameters of char during gasification with different oxidizers
| Oxidizing reagent | k os /s−1 or kov/s−1 | E/kJ mol−1 | n |
|---|---|---|---|
| Oxygen | 1.16 × 104 | 114 | 0.88 |
| Carbon dioxide | 5.96 × 106 | 227 | 0.39 |
| Steam | 1.09 × 106 | 193 | 0.30 |
Analysis of results shown in Fig. 2d–f concerning the effect of concentration of oxidizing reagents on the conversion leads to the conclusion that the same kinetic models, as discussed above, can be also applied for the whole range of concentration of gaseous reagent. Figure 5 shows the application of the kinetic models discussed earlier to experimental results obtained during gasification of sewage sludge char under reactive gas atmospheres containing different amounts of the oxidizing agent.
Plots of the linearized model equations for gasification of sewage sludge char by oxygen at 500 °C and steam at 850 °C. Effect of gasifying agent concentration
Citation: Journal of Thermal Analysis and Calorimetry J Therm Anal Calorim 104, 2; 10.1007/s10973-010-1032-1
The shrinking core model was found again to be the most suitable one for all studied concentrations of oxygen and carbon dioxide. As an example, the data for oxygen are shown in Fig. 5a. It is worth to notice that this model is also valid for 100% O2; however, in this case the upper limit of its applicability is only to about 85% of conversion. Figure 5b confirms that the first-order reaction model gives a good prediction of experimental data for steam gasification process in the studied range of H2O concentration.
The gasification and combustion of char are the complex reactions taking place according to several steps as summarized in the article by Di Blasi [4]. In general, the gasification or combustion reaction is initiated by reversible adsorption of gasifying species on active carbon site followed by surface reaction and gaseous products formation. Taking into account the detailed mechanism of gasification process, the Langmuir–Hinshelwood type of kinetic equation describing effect of gasifying reagent concentration on the overall reaction rate can be derived. In thermogravimetric measurements where the product concentrations are low enough and/or the inhibiting effect exerted by the product gases can be ignored, the more complicated Langmuir–Hinshelwood equation is often approximated by simple form represented by Eq. 3 [4].
The reaction rate constants determined for various concentrations of gasifying reagent were presented in double-log plot in Fig. 6. These results were used to determine parameter n in Eq. 3 which is a formal reaction order with respect to oxidizing agent. The values of parameter n for different gases are given in Table 3.
The effect of oxidizers concentration on reaction rate constant
Citation: Journal of Thermal Analysis and Calorimetry J Therm Anal Calorim 104, 2; 10.1007/s10973-010-1032-1
An examination of the results of the biomass gasification kinetics evaluation shows that the exponent of the gaseous reactant pressure is around 0.4–1 [4]. The higher value of reaction order for oxygen n = 0.88 and the lower value of reaction order with respect to CO2n = 0.39 are in accordance with the literature data. However, the value 0.3 for steam gasification is lower, we have to notice that this value was obtained for sewage sludge, which is not the same as lignocellulosic chars analysed by Di Blasi [4]. It is known that differences in char reactivity and values of kinetic parameters (activation energy and reaction orders) are caused by the biomass property, especially by the ash content due to its catalytic properties. The lower value of the parameter n reflects the strong inhibiting effects of steam and carbon dioxide adsorption on the gasification rate.
Conclusions
Char samples obtained by pyrolysis of municipal sewage sludge were gasified in a thermobalance at atmospheric pressure with oxygen, carbon dioxide or steam to study their reactivity at different temperatures and oxidizing agent concentrations. The thermogravimetric experiments performed in a dynamic mode with constant heating rate showed that oxygen reacts with char at relatively low temperatures. In this case the reaction starts at about 400 °C, whereas carbon dioxide and water vapour react with char only at above 700–750 °C.
To understand the behaviour of pyrolysis char during gasification, several models have been used with different degrees of complexity. In this study, the most common and simpler rate models for gas–solid reaction (volumetric and shrinking core models) have been applied to describe conversion of char during gasification processes. The shrinking core model for reaction-controlled regime was found to be the best for predicting the rate of char gasification up to 90% conversion in CO2 and in O2 atmosphere. The experimental data for steam gasification of the char were fitted best by the first-order kinetics.
The activation energies and pre-exponential factors were calculated for char gasification with different oxidizing agents using the most suitable models. In addition, the reaction orders in respect to the concentration of each oxidizing agent were determined. These values as well as the activation energies obtained in this study are in the range of values reported in the literature for coal and biomass char gasification processes.
List of symbols
| α |
Conversion (–) |
| C |
Concentration (mol dm−3) |
| d 0 |
Initial sample particle diameter (m) |
| E |
Activation energy (kJ mol−1) |
| K |
Surface reaction rate constant (s−1) |
| m(t) |
Sample mass at any time (g) |
| m 0 |
Initial mass (g) |
| m k |
Final mass (g) |
| n |
Reaction order (–) |
| R |
Universal gas constant (kJ mol−1 K−1) |
| r s |
Structural term (–) |
| t |
Time (s) |
| T |
Temperature (K) |
| y g |
Concentration of oxidizing agent (mole frac) |
This study was performed in the frames of project: REduction MOdification & VALorisation of Sludge Contract nr: FP6-018525, European Union Research, Sixth framework Programme, Priority 1.1.6.3: Global change and ecosystems.
References
1. Fytili, D, Zabaniotou, A. Utilization of sewage sludge in EU application of old and new methods - A review. Renew Sustain Energy Rev 2008 12:116–140 .
2. Werther, J, Ogada, T. Sewage sludge combustion. Progr Energy Comb Sci. 1999 25:55–116 .
3. Cetin, E, Moghtaderi, B, Gupta, R, Wall, TF. Influence of pyrolysis conditions on the structure and gasification reactivity of biomass chars. Fuel 2004 83:2139–2150 .
4. Di Blasi, C. Combustion and gasification rates of lignocellulosic chars. Progr Energy Comb Sci.. 2009;35:121–140 .
5. Molina, A, Mondragón, F. Reactivity of coal gasification with steam and CO2. Fuel 1998 77:1831–1839 .
6. Kajitani, S, Suzuki, N, Ashizawa, M, Hara, S. CO2 gasification rate analysis of coal char in entrained flow coal gasifier. Fuel 2006 85:163–169 .
7. Fermoso, J, Arias, B, Pevida, C, Plaza, MG, Rubiera, F, Pis, JJ. Kinetic models comparison for steam gasification of different nature fuel chars. J Therm Anal Calorim. 2008 91:779–786 .
8. Strezov, V, Moghtaderi, B, Lucas, JA. Thermal study of decomposition of selected biomass samples. J Therm Anal Calorim. 2003 72:1041–1048 .
9. Cormos, CC, Starr, F, Tzimas, E, Peteves, S. Innovative concepts for hydrogen production processes based on coal gasification with CO2 capture. Int J Hydrogen Energy 2008 33:1286–1294.
10. Butterman, HC, Castaldi, MJ. Influence of CO2 injection on biomass gasification. Ind Eng Chem Res 2007 46:8875–8886 .
11. Dogru, M, Midilli, A, Howarth, CR. Gasification of sewage sludge using a throated downdraft gasifier and uncertainty analysis. Fuel Process Technol 2002 75:55–82 .
12. Reed, GP, Paterson, NP, Zhuo, Y, Dugwell, DR, Kandiyoti, R. Trace element distribution in sewage sludge gasification: source and temperature effects. Energy Fuels 2005 19:298–304 .
13. Manya, JJ, Sanchez, JL, Gonzalo, A, Arauzo, J. Air gasification of dried sewage sludge in a fluidized bed: effect of the operating conditions and in-bed use of alumina. Energy Fuels 2005 19:629–636 .
14. Petersen, I, Werther, J. Experimental investigation and modeling of gasification of sewage sludge in the circulating fluidized bed. Chem Eng Process. 2005 44:717–736 .
15. Petersen, I, Werther, J. Three-dimensional modeling of a circulating fluidized bed gasifier for sewage sludge. Chem Eng Sci. 2005 60:4469–4484 .
16. Pinto, F, Lopes, H, Andre, RN, Dias, M, Gulyurtlu, I, Cabrita, I. Effect of experimental conditions on gas quality and solids produced by sewage sludge cogasification. 1. Sewage sludge mixed with coal. Energy Fuels 2007 21:2137–2145 .
17. Aznar, M, Manyà, JJ, García, G. Influence of freeboard temperature, fluidization velocity, and particle size on tar production and composition during the air gasification of sewage sludge. Energy Fuels 2008 22:2840–2850 .
18. Groß, B, Eder, C, Grziwa, P. Energy recovery from sewage sludge by means of fluidized bed gasification. Waste Manag Res 2008 28:1819–1826 .
19. Santacesaria, E. Fundamental chemical kinetics: the first step to reaction modelling and reaction engineering. Catal Today. 1999;52:113–123 .
20. Liliedahl, T, Sjoestroem, K. Modelling of char-gas reaction kinetics. Fuel 1997 76 1 29–37 .
21. Johnson JL . Kinetics of coal gasification. New York: Krieger Publishing Company; 1979.
22. Ozbas, KE, Koek, MV, Hicyilmaz, C. Comparative kinetic analysis of raw and cleaned coals. J Therm Anal Calorim. 2002 69:541–549 .
23. Koek, MV. Temperature-controlled combustion and kinetics of different rank coal samples. J Therm Anal Calorim.. 2005;79:175–180 .
24. Henrich, E, Buerkle, S, Meza-Renken, ZI, Rumpel, S. Combustion and gasification kinetics of pyrolysis chars from waste and biomass. J Anal Appl Pyrolysis. 1999 49:221–241 .
25. Klose, W, Woelki, M. On the intrinsic rate of biomass char gasification with carbon dioxide and steam. Fuel. 2005 84:885–892 .
26. Scott, SA, Davidson, JF, Dennis, JS, Fennell, PS, Hayhurst, AN. The rate of gasification by CO2 of chars from waste. Proc Combust Inst. 2005 30:2151–2159 .
27. Inguanzo, M, Menendez, JA, Fuente, E, Pis, JJ. Reactivity of pyrolyzed sludge in air and CO2. J Anal Appl Pyrolysis. 2001 58–59:943–954 .
28. Bedyk, T, Nowicki, L, Stolarek, P, Ledakowicz, S. Effect of CaO and dolomite additive in the thermal decomposition of sewage sludge in an inert atmosphere. J Residuals Sci Technol. 2009 6 1 3–10.
29. Baker, RR. Kinetic parameters from the non-isothermal decomposition of a multi-component solid. Thermochim Acta.. 1978;23 2 201–212 .
30. 1976 Szekely, J, Ewans, JW, Sohn, HI Gas–solid reactions Academic Press New York.
