View More View Less
• 1 Robert Bosch Department of Mechatronics, Faculty of Mechanical Engineering and Informatics, University of Miskolc, Miskolc-Egyetemváros, H-3515, Hungary
Open access

## Abstract:

This paper deals with the dynamical analysis of a crane model. Truss finite elements are used to discretize the suspending chains with the so called updated Lagrangian description. This nonlinear model is regarded to be the best approximation to which linear models are compared. The inertia and independent degrees of freedom are also taken into consideration by linear models. The goal is to find a linear model, which can be used as an observer in antisway control of a crane.

## Abstract:

This paper deals with the dynamical analysis of a crane model. Truss finite elements are used to discretize the suspending chains with the so called updated Lagrangian description. This nonlinear model is regarded to be the best approximation to which linear models are compared. The inertia and independent degrees of freedom are also taken into consideration by linear models. The goal is to find a linear model, which can be used as an observer in antisway control of a crane.

## 1 Introduction

Usually very simple mathematical pendulum models of the cranes are applied in papers [1]-[7]. The mass and its independent degree of freedom of the ropes/chains are neglected in these models. Though it is advantages to use a simple model as an observer in anti-sway control of cranes, but it may leads to inaccuracy in state space variables.

In this paper nonlinear and linear dynamical models of an overhead crane with chains will be formulated and analyzed. In addition to the payload, the inertia and independent Degree of Freedom (DoF) of the suspending chains are also considered.

Finite Element Method (FEM) is well applicable for the formulation of nonlinear and linear static and dynamic problems [8], [9]. The suspending chain perfectly flexible, i.e. it has no bending stiffness. The nonlinear model can be derived by the help of truss elements which can transfer only axial force [10] and perform 2D motions. The linear model practically is a taut string [11], which is discretized also with two node linear elements approximating only lateral motions. The solutions of the linear models are compared to the nonlinear counterpart.

## 2 Equations of motions of the crane models

The picture of a crane model is shown in Fig. 1. It is assumed that the displacements of the two parallel chains are the same therefore a single chain with double mass is a good substitution in a dynamical analysis. The chain is regarded as elastic, one dimensional structure, and can transmit only axial force along its x1 coordinate. The motion of the structure in plane (x, y) is investigated with nonlinear and linear approaches.

### 2.1 Nonlinear model

In order to treat the nonlinear model of the overhead crane an incremental form of the principle of the virtual displacements with updated Lagrangian formulation [10] is used:
$∫Vtptu¨t+Δtδu dVt+Mu¨Mt+Δtδu M +∫VtE e11t δe11 dVt+∫Vtσ11t δη11 dV= ∫Vtρtg δu dVt−M gδvM−∫Vtσ11t δe11 dVt,$
where ρt is the density of the material in the deformed configuration; $u¨t+Δt$ is a 2D vector of the accelerations at time t+$Δ$t; δu is the 2D vector of the virtual displacements; Vt is the volume of the structure at time t; M is the mass of the payload; δu M is the 2D vector of the virtual displacements of mass M; g is the 2D vector of the gravity acceleration g; E is the Young’s modulus; $e11t$ = du / d x1 is the linear strain measured in axial direction in deformed configuration at time t; δe11 is the variation of the linear strain at the configuration time t; $σ11t$ is the Cauchy stress of the one dimensional structure at time t; δη11 is the variation of the quadratic portion of the nonlinear strain at the configuration time t. The quadratic portion of the nonlinear strain increment is written as
$δη11=12δ[(∂u¯∂x1)2 + (∂v¯∂x1)2] ,$
where $u¯$ and $v¯$ are the increments in displacements in axial x1 and its perpendicular direction, respectively. It is noted that (2) can be expressed also with global Cartesian displacement increments u, v
$δη11=12δ[(∂u∂x1)2+ (∂v∂x1)2] .$
Truss elements are used to discretize (1). A truss element is a two node straight line member capable to transfer axial force only. Deformed length of the element is Lt , coordinate ξ measures the distance along the truss element, positive from node i to node j. The approximations for the axial displacement $u¯e(ξ)$ and its perpendicular displacement $v¯e(ξ)$ along the element e are given as:
$u¯e(ξ)=(1−ξLt) u¯i + ξLt u¯j ,$
$v¯e(ξ)=(1−ξLt) v¯i+ξLtv¯j ,$
where $u¯i$, $u¯j$ and $v¯i$ $v¯j$ are the increments in nodal displacements at element local coordinate system (see Fig. 2a). It is noted that dx1 = .
The local nodal displacement increments $u¯i$, $u¯j$ and $v¯i$ $v¯j$ can be related to the global Cartesian node displacement increments $u¯i$, $u¯j$ and $v¯i$ $v¯j$ (see Fig. 2b) via the following transformation:
$[u¯iu¯jv¯iv¯j] = [xj−xiLt yj−yiLt 0 0−yj−yiLt xj−xiLt 0 0 0 0 xj−xiLt yj−yiLt 0 0 −yj−yiLt xj−xiLt] [uiujvivi].$

It is also noted that the relation between the nodal forces in local and global coordinates are expressed similar way as (6), only the nodal displacements are replaced with nodal forces. The same transformation is also valid for the nodal accelerations.

The global Cartesian displacements in (3) and accelerations in (1) are approximated by the same linear interpolation functions as in (4) and (5):
$ue(ξ)=(1−ξLt)ui+ξLtuj ,$
$ve(ξ)=(1−ξLt)vi+ξLtvj ,$
$u¨e(ξ)=(1−ξLt)u¨ i+ξLtu¨j ,$
$v¨e(ξ)=(1−ξLt)v¨ i+ξLtv¨j ,$
where $u¨i ,u¨j v¨i,v¨j$ are nodal accelerations.

The coordinates of the vector of displacement variation δu are approximated in the same way as the functions of (4), (5) and (7), (8).

Using (2)-(10) to determine the integrals in (1), it provides element mass matrix
$M¯e=ρtAtLt6[2 0 1 00 2 0 11 0 2 00 1 0 2]$
linear and geometric element stiffness matrices $K¯Le$ and $K¯Ge$ on the left hand side of
$K¯Le=AtELt[1 0 −1 00 0 0 0−1 0 1 00 0 0 0], K¯Ge=Atσ11Lt[1 0 −1 00 1 0 −1−1 0 1 00 −1 0 0],$
the external and internal load vectors $f¯Ge$, $f¯σe$ the right hand site of (1) in element local coordinate system on
$f¯Ge=−gρtAtLt2[yj−yiLtxj−xiLtyj−yiLtxj−xiLt], f¯σe=Atσ11t[−1010] ,$
where At$σ11t$ = Nt is the axial force of the truss element.
The element matrices are transformed to the global Cartesian coordinate system with the help of (6) then assembled according to the usual FEM process. The obtained equation of motion associated to (1) is written in matrix form as follows:
$Mt+Δt q¨ +(KLt+KGt)Δq = fgt+Δt−fσt ,$
where Mt+∆t is the structural mass matrix; $KLt$ and $KGt$ are the structural linear and geometric stiffness matrices; fgt+∆t is the structural column vector of external loads; fσt is the structural column vector of internal loads; $q¨$ is the structural column vector of nodal accelerations; ∆q is the structural column vector of the increments in nodal displacements. It is noted that the mass matrix is a constant matrix, i.e. is time invariant

M = Mt+∆t , since the mass of the structure does not change in time.

The equation of motion (14) can be integrated numerically, e.g. by Newmark method. The steps of this method [10] are summarized as follows:
1. I.Initially the stiffness matrices KtL , KtG and the mass matrix M are formed and set the initial value of the displacements q0 , the velocity $q˙0$ and the accelerations $q¨0$ .
2. II.Form of the effective stiffness matrix at time t
$K^=KLt+KGt+4Δt2M$
1. III.Form of the effective load vector $f^$ at time t+∆t
$f^=fgt+Δt+M(4Δtqt+q˙t)−fσt$
1. IV.Solve the linear equation for the displacement increment ∆q(0)
$K^Δq(i)=f^, where i=0 .$
1. V.Iteration for dynamic equilibrium
2. (a)i =i + 1
3. (b)Calculate (i−1)st approximation to accelerations, velocities, and displacements
$q¨(i−1)t+Δt=4Δt2Δq(i-1)−4Δt2q˙t−q¨t$
$q˙(i−1)t+Δt=4ΔtΔq(i−1)−q˙t,$
$q(i−1)t+Δt=Δq(i−1)−qt.$
1. (c)Calculate (i −1)st effective out of balance load vector
2. (d)Solve for the i’th correction to displacement increment
$f^(i−1)t+Δt=fgt+Δt−Mq¨(i−1)t+Δt−fσ(i−1)t+Δt.$
$K^Δq^(i)=f^(i-1)t+Δt.$
1. (e)Calculate new displacement increments
$Δq(i)=Δq(i−1)+Δq^(i).$
1. (f) Iteration is terminated if $‖Δq^(i)‖2‖q(i)t+Δt‖2$tol otherwise back to step (a). The value of tol is prescribed by the user, its magnitude is10−6
2. VI.If convergence ∆q = ∆q(i) then accelerations, velocities, and displacements are determined as:
$q¨t+Δt=4Δt2Δq−4Δtq˙t−q¨t,$
$q˙t+Δt=qt+0.5Δt(q¨t+q¨t+Δt),$
$qt+Δt=qt+Δq.$

### 2.2 Linear crane model

Usually linear counterpart of the nonlinear equation of motion is needed in order to design a controller for a dynamical system. The crane model made of chain shown in Fig. 3 can be regarded as a taut string, which suffers relatively small lateral displacements. The axial force of the string due to gravity force is calculated in the rest position and assumed to be constant in the course its motion.

The linear equation (1D model) of motion of the crane can be derived by the help of the virtual displacements written for a taut string
$∫Voρ0 u¨t δu dV0+Mu¨Mt δu+∫V0σ110δ(12ut2)dV0=Rt,$
where ρ0 is the density of the material at time zero;$u¨t$ is the acceleration function in lateral direction; i.e. in horizontal direction at time t ; δu is the virtual lateral displacement function; V0 is the volume of the structure at time 0 ; M is the mass of the payload; $u¨Mt$ and δuM is the acceleration and virtual lateral displacements of mass $M; σ110$ is the function of the axial stress due to gravity force determined in the rest position of the crane; and Rt is the virtual work of the external force obtained from displacement control.
One dimensional linear line elements are used to discretize (27). The horizontal displacement is approximated along an element in local coordinate system:
$ue(ξ)=(1−ξL0)ui+ ξL0uj ,$
Where, ui , uj are the horizontal nodal displacements of the element e.
The horizontal acceleration along an element is approximated also with the same interpolation functions
$u¨e(ξ)=(1−ξL0)u¨i+ξL0u¨j ,$
where $u¨i$,$u¨j$ are horizontal nodal accelerations of the element e .
Substituting (28) and (29) into (27) the element mass matrix Me and stiffness matrix Ke can be derived
$Me=ρ0A0L06[2 11 2], Ke=A0σ11[1 11 1], qe=[uiuj], q¨e=[u¨iu¨j] ,$
where $qe$ is the element nodal displacement vector and $q¨e$ is the element nodal acceleration vector, which are generated directly by the global Cartesian horizontal displacement approximation therefore no transformation is needed before assembling the structural matrices.
The linear equation of motion of the crane model is written as:
$Mq¨ + Kq = ft,$
where M and K is the structural mass and stiffness matrices, ft is the column vector of the external forces due to displacement control, q is the structural vector of nodal displacements, $q¨$ is the structural vector of nodal accelerations.
The linear differential equation (31) can be given also in state space form introducing new variables q = x1 and $q˙$= x2 :
$x˙ = Ax + bu ,$

Where $X=[x1x2] , A=[ 0 I−M-1 K 0] , bu=[0−M−1 ft] ,$ and I is a unit matrix.

Numerical integration of (32) can be performed with number of standard methods, e.g. Runge-Kutta method or trapezoid rule, using Matlab or Scilab software system.

### 2.3 Numerical examples

Nonlinear and linear FEM programs have been developed using the above theory. The length of the chains is 0.8 m, and it is subdivided into 10 uniform finite elements. The linear version will be analyzed also with an FE mesh of two elements chain models. The mass of the chain is 0.22 kg and two different payloads are exerted on the crane, the heavy one is 0.42 kg, the light one is 0.07 kg.

In order to compare their performances a simple crane motion will be simulated. In the beginning the trolley is moving with constant velocity v1 = 0.8m/s along length x1 = 0.8m , then it stops suddenly, thereafter the payload and the suspending chain will swing freely.

Motions of the cranes obtained for heavy payload using linear and nonlinear models are displayed in Fig. 4. It is clearly seen that the payload performs only horizontal motions in Fig. 4b. However the deformed shapes of the chains for both models are comparable in Fig. 4a and Fig. 4b.

The computations have been performed for heavy and light payloads. The results are given in reference coordinate system and in relative coordinate system attached to the trolley, which are called in the sequel absolute and relative motions, respectively. Absolute and relative motions of the payloads and the relative motions of the middle of the chain are shown in Fig. 5 - Fig. 7.

The displacements of nonlinear and linear models for heavy payload show good agreement in Fig. 5a and Fig. 6a, while the discrepancies are bigger for the light one in Fig. 5b and Fig. 6b.

It is clear from Fig. 7a and Fig. 7b that the chain vibration is significant. The discrepancies between the nonlinear and linear models are negligible for the heavy payload in the beginning (see Fig. 7a), then only relatively small shift can be detected later on. Except in the beginning the results of chain vibrations are less similar for light payload (see Fig. 7b). However during the controlling of the crane, the displacement of the payload is enforced to be close to the real motion of the crane. Therefore, a small shift in the solution is not a major problem.

## 4 Conclusion

The main goal of this investigation was to find linear models, which can be used as an observer in anti-sway control of the crane. Nonlinear and linear models have been used to simulate the motion of an overhead crane. The results confirmed the assumption that the vibration of the suspending chain is significant and advisable to take into consideration in linear models. The linear model with two finite elements provided also acceptable results compared to ten element mesh, therefore it is a good candidate to use as an observer.

## Acknowledgements

The described article was carried out as part of the EFOP-3.6.1-16-2016-00011 ‘Younger and Renewing University - Innovative Knowledge City - institutional development of the University of Miskolc aiming at intelligent specialization’ project implemented in the framework of the Szechenyi 2020 program. The realization of this project is supported by the European Union, co-financed by the European Social Fund.

## References

• [1]

Wahyudi, Jalani J., Muhida R., Salami M. J. E. Control strategy for automatic Gantry Crane systems: A practical and intelligent approach, International Journal of Advanced Robotic Systems, Vol. 4, No. 4, 2007, pp. 447456.

• Crossref
• Export Citation
• [2]

Won I. S., Hoang N. Q., Lee S. G., Ryu J. K. Comparative study of energy-based control design for overhead cranes, International Robotics and Automation Journal , Vol. 4, No. 3, 2018, pp. 197203.

• Crossref
• Export Citation
• [3]

Kaur A., Priyahansha, Kumari S., Singh T. Position control of overhead cranes using fuzzy controller, International Journal of Advanced Research in Electrical, Electronics and Instrumentation Engineering, Vol. 3, No. 5, 2014, pp. 93419350.

• Export Citation
• [4]

Almutairi N. B., Zribi M. Fuzzy controllers for a Gantry Crane system with experimental verifications, Mathematical Problems in Engineering, Vol. 2016, Paper No. 1965923, pages 117.

• Crossref
• Export Citation
• [5]

Ahmad M. A. Active Sway suppression techniques of a Gantry Crane system, European Journal of Scientific Research, Vol. 27, No. 3, 2009, pp. 322333.

• Export Citation
• [6]

Ospina-Henao P. A., L´opez-Suspes F. Dynamic analysis and control PID path of a model type gantry crane, Journal of Physics, Conf. Series, Vol. 850, 2017, pages 114.

• Crossref
• Export Citation
• [7]

Kharola1 A., Patil P. Mathematical modeling and performance comparison of overhead cranes using soft-computing techniques, International Journal of Mechatronics, Electrical and Computer Technology, Vol. 7, No. 23, 2017, pp. 31883200.

• Export Citation
• [8]

Vătăman A., Ciutina A., Grecea D. Numerical analysis of short link steel eccentrically braced frames under seismic action, Pollack Periodica, Vol. 11, No. 2, 2016, pp. 2942.

• Crossref
• Export Citation
• [9]

Hajdu F., Szalai P., Mika P., Kuti R. Parameter identification of a fire truck suspension for vibration analysis, Pollack Periodica, Vol. 14, No. 3, 2019, pp. 5162.

• Crossref
• Export Citation
• [10]

Bathe K. J. Finite element procedures, Prentice Hall, Pearson Education Inc, 2006.

• [11]

Meirovich L. Fundamentals of vibrations, McGraw-Hill, New York, 2001.

• [1]

Wahyudi, Jalani J., Muhida R., Salami M. J. E. Control strategy for automatic Gantry Crane systems: A practical and intelligent approach, International Journal of Advanced Robotic Systems, Vol. 4, No. 4, 2007, pp. 447456.

• Crossref
• Export Citation
• [2]

Won I. S., Hoang N. Q., Lee S. G., Ryu J. K. Comparative study of energy-based control design for overhead cranes, International Robotics and Automation Journal , Vol. 4, No. 3, 2018, pp. 197203.

• Crossref
• Export Citation
• [3]

Kaur A., Priyahansha, Kumari S., Singh T. Position control of overhead cranes using fuzzy controller, International Journal of Advanced Research in Electrical, Electronics and Instrumentation Engineering, Vol. 3, No. 5, 2014, pp. 93419350.

• Export Citation
• [4]

Almutairi N. B., Zribi M. Fuzzy controllers for a Gantry Crane system with experimental verifications, Mathematical Problems in Engineering, Vol. 2016, Paper No. 1965923, pages 117.

• Crossref
• Export Citation
• [5]

Ahmad M. A. Active Sway suppression techniques of a Gantry Crane system, European Journal of Scientific Research, Vol. 27, No. 3, 2009, pp. 322333.

• Export Citation
• [6]

Ospina-Henao P. A., L´opez-Suspes F. Dynamic analysis and control PID path of a model type gantry crane, Journal of Physics, Conf. Series, Vol. 850, 2017, pages 114.

• Crossref
• Export Citation
• [7]

Kharola1 A., Patil P. Mathematical modeling and performance comparison of overhead cranes using soft-computing techniques, International Journal of Mechatronics, Electrical and Computer Technology, Vol. 7, No. 23, 2017, pp. 31883200.

• Export Citation
• [8]

Vătăman A., Ciutina A., Grecea D. Numerical analysis of short link steel eccentrically braced frames under seismic action, Pollack Periodica, Vol. 11, No. 2, 2016, pp. 2942.

• Crossref
• Export Citation
• [9]

Hajdu F., Szalai P., Mika P., Kuti R. Parameter identification of a fire truck suspension for vibration analysis, Pollack Periodica, Vol. 14, No. 3, 2019, pp. 5162.

• Crossref
• Export Citation
• [10]

Bathe K. J. Finite element procedures, Prentice Hall, Pearson Education Inc, 2006.

• [11]

Meirovich L. Fundamentals of vibrations, McGraw-Hill, New York, 2001.

The author instructions template is available in MS Word.

Senior editors

Editor(s)-in-Chief: Iványi, Amália

Editor(s)-in-Chief: Iványi, Péter

Scientific Secretary

Miklós M. Iványi

Editorial Board

• Bálint Bachmann (Institute of Architecture, Faculty of Engineering and Information Technology, University of Pécs, Hungary)
• Jeno Balogh (Department of Civil Engineering Technology, Metropolitan State University of Denver, Denver, Colorado, USA)
• Radu Bancila (Department of Geotechnical Engineering and Terrestrial Communications Ways, Faculty of Civil Engineering and Architecture, “Politehnica” University Timisoara, Romania)
• Charalambos C. Baniotopolous (Department of Civil Engineering, Chair of Sustainable Energy Systems, Director of Resilience Centre, School of Engineering, University of Birmingham, U.K.)
• Oszkar Biro (Graz University of Technology, Institute of Fundamentals and Theory in Electrical Engineering, Austria)
• Ágnes Borsos (Institute of Architecture, Department of Interior, Applied and Creative Design, Faculty of Engineering and Information Technology, University of Pécs, Hungary)
• Matteo Bruggi (Dipartimento di Ingegneria Civile e Ambientale, Politecnico di Milano, Italy)
• Ján Bujňák (Department of Structures and Bridges, Faculty of Civil Engineering, University of Žilina, Slovakia)
• Anikó Borbála Csébfalvi (Department of Civil Engineering, Institute of Smart Technology and Engineering, Faculty of Engineering and Information Technology, University of Pécs, Hungary)
• Mirjana S. Devetaković (Faculty of Architecture, University of Belgrade, Serbia)
• Szabolcs Fischer (Department of Transport Infrastructure and Water Resources Engineering, Faculty of Architerture, Civil Engineering and Transport Sciences Széchenyi István University, Győr, Hungary)
• Radomir Folic (Department of Civil Engineering, Faculty of Technical Sciences, University of Novi Sad Serbia)
• Jana Frankovská (Department of Geotechnics, Faculty of Civil Engineering, Slovak University of Technology in Bratislava, Slovakia)
• János Gyergyák (Department of Architecture and Urban Planning, Institute of Architecture, Faculty of Engineering and Information Technology, University of Pécs, Hungary)
• Kay Hameyer (Chair in Electromagnetic Energy Conversion, Institute of Electrical Machines, Faculty of Electrical Engineering and Information Technology, RWTH Aachen University, Germany)
• Elena Helerea (Dept. of Electrical Engineering and Applied Physics, Faculty of Electrical Engineering and Computer Science, Transilvania University of Brasov, Romania)
• Ákos Hutter (Department of Architecture and Urban Planning, Institute of Architecture, Faculty of Engineering and Information Technolgy, University of Pécs, Hungary)
• Károly Jármai (Institute of Energy and Chemical Machinery, Faculty of Mechanical Engineering and Informatics, University of Miskolc, Hungary)
• Teuta Jashari-Kajtazi (Department of Architecture, Faculty of Civil Engineering and Architecture, University of Prishtina, Kosovo)
• Róbert Kersner (Department of Technical Informatics, Institute of Information and Electrical Technology, Faculty of Engineering and Information Technology, University of Pécs, Hungary)
• Rita Kiss  (Biomechanical Cooperation Center, Faculty of Mechanical Engineering, Budapest University of Technology and Economics, Budapest, Hungary)
• István Kistelegdi  (Department of Building Structures and Energy Design, Institute of Architecture, Faculty of Engineering and Information Technology, University of Pécs, Hungary)
• Stanislav Kmeť (President of University Science Park TECHNICOM, Technical University of Kosice, Slovakia)
• Imre Kocsis  (Department of Basic Engineering Research, Faculty of Engineering, University of Debrecen, Hungary)
• László T. Kóczy (Department of Information Sciences, Faculty of Mechanical Engineering, Informatics and Electrical Engineering, University of Győr, Hungary)
• Dražan Kozak (Faculty of Mechanical Engineering, Josip Juraj Strossmayer University of Osijek, Croatia)
• György L. Kovács (Department of Technical Informatics, Institute of Information and Electrical Technology, Faculty of Engineering and Information Technology, University of Pécs, Hungary)
• Balázs Géza Kövesdi (Department of Structural Engineering, Faculty of Civil Engineering, Budapest University of Engineering and Economics, Budapest, Hungary)
• Tomáš Krejčí (Department of Mechanics, Faculty of Civil Engineering, Czech Technical University in Prague, Czech Republic)
• Jaroslav Kruis (Department of Mechanics, Faculty of Civil Engineering, Czech Technical University in Prague, Czech Republic)
• Miklós Kuczmann (Department of Automations, Faculty of Mechanical Engineering, Informatics and Electrical Engineering, Széchenyi István University, Győr, Hungary)
• Tibor Kukai (Department of Engineering Studies, Institute of Smart Technology and Engineering, Faculty of Engineering and Information Technology, University of Pécs, Hungary)
• Maria Jesus Lamela-Rey (Departamento de Construcción e Ingeniería de Fabricación, University of Oviedo, Spain)
• János Lógó  (Department of Structural Mechanics, Faculty of Civil Engineering, Budapest University of Technology and Economics, Hungary)
• Carmen Mihaela Lungoci (Faculty of Electrical Engineering and Computer Science, Universitatea Transilvania Brasov, Romania)
• Frédéric Magoulés (Department of Mathematics and Informatics for Complex Systems, Centrale Supélec, Université Paris Saclay, France)
• Gabriella Medvegy (Department of Interior, Applied and Creative Design, Institute of Architecture, Faculty of Engineering and Information Technology, University of Pécs, Hungary)
• Tamás Molnár (Department of Visual Studies, Institute of Architecture, Faculty of Engineering and Information Technology, University of Pécs, Hungary)
• Ferenc Orbán (Department of Mechanical Engineering, Institute of Smart Technology and Engineering, Faculty of Engineering and Information Technology, University of Pécs, Hungary)
• Zoltán Orbán (Department of Civil Engineering, Institute of Smart Technology and Engineering, Faculty of Engineering and Information Technology, University of Pécs, Hungary)
• Dmitrii Rachinskii (Department of Mathematical Sciences, The University of Texas at Dallas, Texas, USA)
• Chro Radha (Chro Ali Hamaradha) (Sulaimani Polytechnic University, Technical College of Engineering, Department of City Planning, Kurdistan Region, Iraq)
• Maurizio Repetto (Department of Energy “Galileo Ferraris”, Politecnico di Torino, Italy)
• Zoltán Sári (Department of Technical Informatics, Institute of Information and Electrical Technology, Faculty of Engineering and Information Technology, University of Pécs, Hungary)
• Grzegorz Sierpiński (Department of Transport Systems and Traffic Engineering, Faculty of Transport, Silesian University of Technology, Katowice, Poland)
• Zoltán Siménfalvi (Institute of Energy and Chemical Machinery, Faculty of Mechanical Engineering and Informatics, University of Miskolc, Hungary)
• Andrej Šoltész (Department of Hydrology, Faculty of Civil Engineering, Slovak University of Technology in Bratislava, Slovakia)
• Zsolt Szabó (Faculty of Information Technology and Bionics, Pázmány Péter Catholic University, Hungary)
• Mykola Sysyn (Chair of Planning and Design of Railway Infrastructure, Institute of Railway Systems and Public Transport, Technical University of Dresden, Germany)
• András Timár (Faculty of Engineering and Information Technology, University of Pécs, Hungary)
• Barry H. V. Topping (Heriot-Watt University, UK, Faculty of Engineering and Information Technology, University of Pécs, Hungary)

POLLACK PERIODICA
Pollack Mihály Faculty of Engineering
Institute: University of Pécs
Address: Boszorkány utca 2. H–7624 Pécs, Hungary
Phone/Fax: (36 72) 503 650

E-mail: peter.ivanyi@mik.pte.hu

Indexing and Abstracting Services:

• SCOPUS

2019
Scimago
H-index
10
Scimago
Journal Rank
0,262
Scimago
Quartile Score
Civil and Structural Engineering Q3
Computer Science Applications Q3
Materials Science (miscellaneous) Q3
Modeling and Simulation Q3
Software Q3
Scopus
Cite Score
269/220=1,2
Scopus
Cite Score Rank
Civil and Structural Engineering 206/310 (Q3)
Computer Science Applications 445/636 (Q3)
General Materials Science 295/460 (Q3)
Modeling and Simulation 212/274 (Q4)
Software 304/373 (Q4)
Scopus
SNIP
0,933
Scopus
Cites
290
Scopus
Documents
68
Acceptance
Rate
67%

Pollack Periodica
Publication Model Hybrid
Submission Fee none
Article Processing Charge 900 EUR/article
Printed Color Illustrations 40 EUR (or 10 000 HUF) + VAT / piece
Regional discounts on country of the funding agency World Bank Lower-middle-income economies: 50%
World Bank Low-income economies: 100%
Further Discounts Editorial Board / Advisory Board members: 50%
Corresponding authors, affiliated to an EISZ member institution subscribing to the journal package of Akadémiai Kiadó: 100%
Subscription Information Online subsscription: 321 EUR / 402 USD
Print + online subscription: 384 EUR / 480 USD
Purchase per Title Individual articles are sold on the displayed price.

Pollack Periodica
Language English
Size B5
Year of
Foundation
2006
Publication
Programme
2021 Volume 16
Volumes
per Year
1
Issues
per Year
3
Founder's
H-1117 Budapest, Hungary 1516 Budapest, PO Box 245.
Publisher's
H-1117 Budapest, Hungary 1516 Budapest, PO Box 245.
Responsible
Publisher
ISSN 1788-1994 (Print)
ISSN 1788-3911 (Online)

Jan 2021 0 27 4
Feb 2021 0 24 17
Mar 2021 0 28 15
Apr 2021 0 28 11
May 2021 0 13 18
Jun 2021 0 9 16
Jul 2021 0 0 0

## Analysis and balance of phosphorous removal from wastewater at urban wastewater treatment plant

Authors: Peter Lukac and Lubos Jurik